Accueil/Ressources/Connaissances/Testing&Analysis/Initial Coulombic Efficiency (ICE): Calculation & Troubleshooting

Initial Coulombic Efficiency (ICE): Calculation & Troubleshooting

Canrd November 13, 2026 86

Initial Coulombic Efficiency (ICE), also called first-cycle Coulombic efficiency, measures charge recovery during a defined first electrochemical cycle. It helps engineers evaluate initial irreversible reactions, compare formation protocols and assess electrode materials. ICE is a charge-based metric rather than a direct measurement of cyclable lithium inventory.

What Is Initial Coulombic Efficiency (ICE)?

Initial Coulombic Efficiency (ICE) describes the fraction of charge recovered relative to the charge supplied on the first electrochemical cycle.

ICE is a charge-based metric. It is not energy efficiency, and it cannot directly quantify the exact amount of recyclable lithium atoms.

ICE Calculation Formula

For a conventional full cell that starts with charging:

For half-cells, define the lithiation and delithiation sequence explicitly before selecting the numerator and denominator.

  • Numerator and denominator must use identical capacity units and mass normalization basis.
  • Integrate all relevant capacity-bearing steps within the defined cycle, including constant-current and constant-voltage steps where applicable. Do not combine steps from different cycles.

Different Calculation Rules for Half-Cells & Full Cells

Tester software labels for charge / discharge can be misleading. Always confirm the electrochemical sequence before calculation:

Test Configuration Electrochemical Sequence ICE Calculation
Cathode half-cell (vs Li metal) Cathode delithiation → lithiation First lithiation capacity ÷ first delithiation capacity ×100%
Anode half-cell (vs Li metal) Anode lithiation → delithiation First delithiation capacity ÷ first lithiation capacity ×100%
Conventional full cell Charge → Discharge First discharge capacity ÷ first charge capacity ×100%

Common trap: Directly applying the simple “discharge / charge” formula on anode half-cells may invert your ICE result, because software naming conventions vary. Always rely on lithiation / delithiation physical process definitions.

Why ICE Differs Between Half-Cells and Full Cells

Half-Cells

A half-cell uses lithium metal foil as the counter electrode, which provides a large lithium reservoir.

  • Cathode half-cell: ICE loss may come from incomplete lithium reinsertion, cathode structural changes, electrolyte oxidation and voltage cutoff limits.
  • Anode half-cell: Useful for evaluating initial lithiation, reversible delithiation, surface side reactions and lithium trapping. Good half-cell ICE does not guarantee strong full-cell ICE. The core reason is that half-cells and full cells operate under different lithium inventory constraints, paired counter-electrodes, and potential windows; lithium metal’s reactivity is an additional influencing factor.

Full Cells

In a conventional, initially unformed full cell without pre-lithiation or supplementary lithium, the cathode is the principal source of cyclable lithium. During initial charging, interphase formation and other irreversible reactions consume part of this inventory. Measured ICE also depends on electrode balancing, voltage limits and accessible capacity. Full-cell ICE therefore cannot be inferred from cathode half-cell ICE alone. No universal rule states full-cell ICE is always lower than cathode half-cell ICE; comparisons require specifying cell configuration, materials and test protocols.

CANRD First-Cycle Efficiency Examples

Full-cell batch test

CANRD’s archived full-cell fabrication case record lists the following first-cycle results:

Cell First charge capacity, mAh First discharge capacity, mAh Reported ICE
1 1743 1541 88.4%
2 1735 1534 88.4%
3 1731 1534 88.6%
4 1737 1539 88.6%
5 1734 1538 88.7%
6 1732 1530 88.3%
7 1740 1541 88.6%
8 1749 1548 88.5%
9 1728 1529 88.5%
10 1740 1538 88.4%

For Cell 1:

The measured first-cycle capacity difference is: 

Across the ten cells, the mean calculated ICE is approximately 88.5%. The 202 mAh difference cannot be fully attributed only to SEI formation. Confirming root causes needs extra characterization of electrodes, electrolyte and test protocol. This dataset only demonstrates calculation and sample variation within this single case, and cannot be used to rank unrelated materials or cell designs.

Silicon-carbon material half-cell test

A CANRD silicon-carbon material test table shows how test conditions change ICE and reversible capacity:

Condition label First reversible specific capacity Measured ICE
1.5 V 1994.7 mAh/g 92.1%
0.8 V 1788.7 mAh/g 82.6%

These results prove ICE values must always be published alongside full test conditions. These half-cell results cannot directly predict full-cell ICE performance. Before comparing supplier data, request the complete voltage window, current, constant-voltage termination condition, temperature, electrode loading and electrolyte formulation.

What Causes Low Initial Coulombic Efficiency?

  1. SEI Layer Formation: Electrolyte reduction on anode surfaces builds the SEI (Solid Electrolyte Interphase) film. A stable SEI suppresses further electrolyte decomposition, but its initial formation consumes charge and cyclable lithium. Continuous interphase growth can trigger extra losses in later cycles.
  2. Lithium Trapping & Poor Reversibility: Lithium may get trapped inside reaction byproducts or inaccessible regions of active materials. Severe material volume deformation and particle pulverization can break electrical contact and reduce recoverable capacity.
  3. Excessive Surface Side Reactions: Exposed surface chemistry, contamination and high specific surface area accelerate electrolyte decomposition. Particle size alone does not control ICE; coating quality, porosity and surface composition also play key roles.
  4. Test-condition limited capacity: Improper cutoff voltage, high polarization or incomplete cycling steps can artificially reduce measured ICE. This type of loss should be separated from permanent lithium consumption.

An apparent ICE above 100% requires investigation. First check the calculation direction, cycle pairing, capacity integration and initial electrode state, including any pre-lithiation. The capacity ratio alone cannot establish manganese dissolution or structural damage.

Practical Troubleshooting Workflow for Low ICE

Observation Primary Check Items Follow-up Evaluation
Low ICE on single cell Cable connections, cycle program, voltage curve anomalies Repeat test with identical protocol + control cell
Low ICE across full material batch Electrode moisture, slurry preparation, electrolyte consistency Test material and electrolyte variants in controlled experiments
Good half-cell ICE, poor full-cell ICE N/P ratio, total lithium inventory, voltage window Characterize each electrode separately, redesign full cell balancing
ICE shifts after protocol change Current density, cutoff voltage, CV hold time, temperature Run matched controlled tests
ICE improved but usable capacity drops Narrow operating window / incomplete material utilization Evaluate absolute capacity, energy density and cycle retention

Change one major factor at a time, or use structured experimental design. Otherwise, observed ICE improvements are hard to attribute to a specific material or process change.

Methods to Improve Initial Coulombic Efficiency

  1. Optimize material surface design: Apply surface passivation coating; tune particle architecture to reduce undesirable electrolyte contact while preserving ion and electron transport. Avoid simply using larger particles as a universal fix; longer lithium diffusion distance may hurt rate capability and capacity utilization.
  2. Optimize electrolyte and formation recipe: Screen electrolyte formulations together with your actual electrode system. Tune formation current, temperature, rest periods and termination conditions, and evaluate outcomes including ICE, reversible capacity, impedance, gas generation and long-term cycling. A higher ICE only delivers value when it supports your target cell performance.
  3. Pre-lithiation: Introduce supplementary lithium sources to compensate lithium inventory losses. Pre-lithiation covers multiple technical routes, including anode modification and lithium-donating additives; it does not only refer to cathode-side pre-lithiation. Pre-lithiation adds lithium inventory, and it does not eliminate the root irreversible side reaction.

FAQs

Q1: What is the difference between ICE and energy efficiency?

A1: ICE (Initial Coulombic Efficiency) is charge-based, calculated by capacity ratio. Energy efficiency accounts for both charge and voltage. These two metrics cannot be interchanged.

Q2: Can cathode half-cell ICE predict full-cell ICE?

A2: No. Full-cell ICE also depends on anode properties, N/P ratio, lithium inventory and voltage operating window. Half-cell results support material screening and mechanistic studies, but do not independently determine full-cell performance.

Q3: Does a higher ICE guarantee longer cycle life?

A3: No. ICE only describes the first cycle. Long-term cycle performance depends on continuous side reactions, material structural stability and operating conditions.

Q4: What details must be included in an ICE test report?

A4: Cell configuration, pre-lithiation status, voltage window, current, CV termination, temperature, electrode loading, normalization basis, electrolyte formula, N/P ratio, replicate data and exact cycle definition.

Conclusion

Initial Coulombic Efficiency (ICE) is a core metric to evaluate first-cycle charge reversibility for battery materials and cells. Half-cell testing reveals electrode behavior under defined half-cell conditions, while full-cell testing reflects real lithium inventory constraints and interphase losses.

When troubleshooting low ICE, engineers should systematically check material surface properties, electrolyte formula, formation protocol and cell balancing rather than only looking at the percentage value. ICE must always be interpreted together with reversible capacity, impedance, gas generation and long-term retention.

Canrd provides custom electrode fabrication, pouch cell prototyping and battery material characterization services for battery R&D teams.